 |
OpenMS
|
Detects peptide pairs in LC-MS data and determines their relative abundance.
| pot. predecessor tools | → FeatureFinderMultiplex → | pot. successor tools |
|---|---|---|
| FileConverter | IDMapper | |
| FileFilter |
FeatureFinderMultiplex is a tool for the fully automated analysis of quantitative proteomics data. It detects pairs of isotopic envelopes with fixed m/z separation. It requires no prior sequence identification of the peptides. In what follows we outline the algorithm. Algorithm The algorithm is divided into three parts: filtering, clustering and linear fitting, see Fig. (d), (e) and (f). In the following discussion let us consider a particular mass spectrum at retention time 1350 s, see Fig. (a). It contains a peptide of mass 1492 Da and its 6 Da heavier labelled counterpart. Both are doubly charged in this instance. Their isotopic envelopes therefore appear at 746 and 749 in the spectrum. The isotopic peaks within each envelope are separated by 0.5. The spectrum was recorded at finite intervals. In order to read accurate intensities at arbitrary m/z we spline-fit over the data, see Fig. (b). We would like to search for such peptide pairs in our LC-MS data set. As a warm-up let us consider a standard intensity cut-off filter, see Fig. (c). Scanning through the entire m/z range (red dot) only data points with intensities above a certain threshold pass the filter. Unlike such a local filter, the filter used in our algorithm takes intensities at a range of m/z positions into account, see Fig. (d). A data point (red dot) passes if
stty: 'standard input': Inappropriate ioctl for device
FeatureFinderMultiplex -- Determination of peak ratios in LC-MS data
Full documentation: http://www.openms.de/doxygen/nightly/html/TOPP_FeatureFinderMultiplex.html
Version: 3.4.0-pre-nightly-2024-12-16 Dec 17 2024, 02:41:12, Revision: 96ad74c
To cite OpenMS:
+ Pfeuffer, J., Bielow, C., Wein, S. et al.. OpenMS 3 enables reproducible analysis of large-scale mass spectrometry data. Nat Methods (2024). doi:10.1038/s41592-024-02197-7.
Usage:
FeatureFinderMultiplex <options>
Options (mandatory options marked with '*'):
-in <file>* LC-MS dataset in either centroid or profile mode (valid formats: 'mzML')
-out <file> Output file containing the individual peptide features. (valid formats: 'featureXML')
algorithmic parameters:
-algorithm:labels <text> Labels used for labelling the samples. If the sample is unlabelled (i.e. you want to detect only single peptide features) please leave this parameter empty. [...] specifies the labels for a single sample. For example
[][Lys8,Arg10] ... SILAC
[][Lys4,Arg6][Lys8,Arg10] ... triple-SILAC
[Dimethyl0][Dimethyl6] ... Dimethyl
[Dimethyl0][Dimethyl4][Dimethyl8] ... triple Dimethyl
[ICPL0][ICPL4][ICPL6][ICPL10] ... ICPL (default: '[][Lys8,Arg10]')
-algorithm:charge <text> Range of charge states in the sample, i.e. min charge : max charge. (default: '1:4')
-algorithm:rt_typical <value> Typical retention time [s] over which a characteristic peptide elutes. (This is not an upper bound. Peptides that elute for longer will be reported.) (default: '40.0') (min: '0.0')
-algorithm:rt_band <value> The algorithm searches for characteristic isotopic peak patterns, spectrum by spectrum. For some low-intensity peptides, an important peak might be missing in one spectrum but be present in one of the neighbouring ones. The algorithm takes a bundle of neighbouring spectra with width rt_band into account. For example with rt_band = 0, all characteristic isotopic peaks have to be present in one and the same spectrum. As rt_band increases, the sensitivity of the algorithm but also the likelihood of false detections increases. (default: '0.0') (min: '0.0')
-algorithm:rt_min <value> Lower bound for the retention time [s]. (Any peptides seen for a shorter time period are not reported.) (default: '2.0') (min: '0.0')
-algorithm:mz_tolerance <value> M/z tolerance for search of peak patterns. (default: '6.0') (min: '0.0')
-algorithm:mz_unit <choice> Unit of the 'mz_tolerance' parameter. (default: 'ppm') (valid: 'Da', 'ppm')
-algorithm:intensity_cutoff <value> Lower bound for the intensity of isotopic peaks. (default: '1000.0') (min: '0.0')
-algorithm:peptide_similarity <value> Two peptides in a multiplet are expected to have the same isotopic pattern. This parameter is a lower bound on their similarity. (default: '0.5') (min: '-1.0' max: '1.0')
-algorithm:averagine_similarity <value> The isotopic pattern of a peptide should resemble the averagine model at this m/z position. This parameter is a lower bound on similarity between measured isotopic pattern and the averagine model. (default: '0.4') (min: '-1.0' max: '1.0')
-algorithm:missed_cleavages <number> Maximum number of missed cleavages due to incomplete digestion. (Only relevant if enzymatic cutting site coincides with labelling site. For example, Arg/Lys in the case of trypsin digestion and SILAC labelling.) (default: '0') (min: '0')
Common TOPP options:
-ini <file> Use the given TOPP INI file
-threads <n> Sets the number of threads allowed to be used by the TOPP tool (default: '1')
-write_ini <file> Writes the default configuration file
--help Shows options
--helphelp Shows all options (including advanced)
INI file documentation of this tool: 
1.9.1